360 Flip / 3 flip / Trey flip
A trick that consists of a kickflip combined with a 360 pop shuvit.
5-0 (Five-O) grind
A grind on the back truck, with the nose pointing up and forward.
A universal unit of measurement for the precision that bearing surfaces are honed to; bearings used for skateboarding range from ABEC 1, the least precise, to ABEC 7, the most precise, though some skateboard bearing manufacturers do not give their bearings a rating.
To air means to jump or ollie, usually off of a ramp; Tony Hawk aired over a police car in Police Academy 3.
This trick can be done with or without grabbing the nose; once in the air the front foot is kicked out and the back foot is kicked back so they are in a walking type position.
A spinning trick on transition that entails spinning to the right while airing to the left, or vice versa.
Everyone who is not a pro.
A grind on the front truck, with the tail pointing back, down, and away from the obstacle.
The pin, threaded on both sides, that rests in the hanger and that the wheels are mounted to.
The nut that screws on to the axle, holding the wheel against the outside of the hanger; it is a 1/2" hex.
The act of your axle slipping one way or another inside the hanger, causing one wheel to lock up; axle slip can be caused by landing primo, though some truck manufacturers guarantee no axle slip.
Backside grab / Melongrab / Melancholy / Mosquito
Grabbing heel edge with your front hand while airing forward or backside.
Any incline used for riding up, completing a trick, and riding back down.
An ollie 180 to switch smith grind *Named after Donny Barley.
Aside from the hanger, it is the other main piece of the truck, used for mounting the truck to the deck.
Skateboard bearings come in a standard size, various precisions, and have 7 or 8 balls enclosed in races between two shields, some of which are removable; one skateboard wheel takes two bearings.
Thick washers placed between the two bearings of a wheel.
A grab in which, after the ollie is initiated, the front foot pulls the board as far forward as possible, the back foot is left to hang in the air, and the back hand grabs the tail of the board before pulling it back under the skater's two feet.
A bigspin with a kickflip incorporated into the spin.
A trick in which the skater and his board both rotate along a vertical axis, but the skater rotates 180 as the board rotates 360 *Alfonso Rawls named this trick after its inventor, Brian Lotti. Rawls thought Lotti sounded like lottery, and since the board was spinning so much during the trick he named it after the California Lottery's Big Spin.
Grabbing right near the front wheel on the heel edge with your front hand, then pushing the tail over to the left (right if goofy foot) by crossing your back leg underneath your front leg.
A slide on the tail or nose, with the respectful truck resting atop the obstacle, and the opposite end of the board pointing up and towards the obstacle.
A slide in which the nose is brought up over the obstacle and the board slides between the two trucks.
The spinning of ones body along its vertical axis while the board does not spin.
Bomb a hill
To skate down a big hill.
A vert or miniramp with concave transition wrapping around 360 degrees, forming a bowl shape.
A big trick involving lots of potential for pain if it is not pulled off; a skater can be called burly if they are partial to these tricks (Jamie Thomas and his tricks are burly).
The cupped washers that are placed on the kingpin, one on top of the small bushing and another underneath the large one.
Rubbery components that surround the kingpin and aid in turning.
Caballerial / Full Cab
The name given to a fakie ollie 360.
The act of making big fast turns usually in a large bowl or transition.
A slide in which the board is flipped for half of a kickflip, then caught with the back foot on the darkside of the tail and the front foot holding up the nose from the griptaped side of the deck, and brought down by the skater into a slide on the peak of the tail
A trick in which the board is flipped for half a kickflip, then caught upside down and flipped back over and spun backside 180 degrees on its vertical axis, all while in the air.
To stop the board from rotating by placing your feet back on the board while in the air.
The act of sliding sideways on all four wheels while on a transition.
When a piece of wood is broken off of the deck.
Once in the air, go into the crucifix position, holding the board out to the side with one hand.
A skateboard composed of all the necessary components; deck, griptape, 4 wheels, two trucks, and bearings; a complete is often referred to as a board.
Describes a curve or transition arced outward.
Any grindable and slidable material attached to an obstacle for easier grinds and slides.
A grind on the front truck, with the tail pointing up, back, and away from the obstacle *Originally called Dan grinds after Dan Paterka, later renamed Koston grinds after Eric, and are now called K-grinds, crooked grinds, or crooks.
The transition created between the bottom of a driveway and the top of a curb that is used as a hip.
A slide in which the board is flipped for half a kickflip, then caught with the back foot on the darkside of the tail and the front foot on the darkside of the nose and brought down by the skater into a slide on the middle of the griptaped side of the deck.
Your board is darkside if it is upside down; the darkside of a deck is the side that the baseplate is mounted to.
The wooden part of the skateboard assembly, made usually of hard maple.
The result of a manufacturers defect when the plys of the deck become unglued and peel apart.
Parks and shops host demos, where pros and ams demonstrate their skateboarding.
Dildo Blades/Fruit Boots
Derogatory terms for in-line skates.
The smacking of the center of the deck on the coping during re-entry into a quarter pipe, mini ramp, etc.
Grab mute right by your front foot and kick off your back foot as if you were a dog taking a piss, hence the name.
A stairway with two sets of stairs seperated by a flat section.
Double sided ledge
A ledge that is narrower than your wheelbase, allowing for boardslides and lipslides without any wheels sliding on top of the ledge.
The act of going from a flat platform into a steep transition.
Any obstacle where a skater can place his tail on the edge of said obstacle and lean forward to drop in to a transition of some kind.
Some skaters will yell this to prevent a collision as they drop in to a section of a crowded park.
A term used to describe a wheel made with two urethanes of different hardnesses; the core is of a hard urethane to better encase the bearing, and the outer part is softer for a smoother ride.
The hardness of urethane used to make a wheel, measured by a number followed by a letter; ex: 98a.
Grabbing your board before leaving the ground or the transition.
On some bowls, quarters, minis or vert ramps, the escalator is the part of the coping that is not parallel to the ground, but rather slopes from one height to another.
A part of a ramp where the transition extends higher than normal.
You are skating fakie if your predominant foot is leading, and will be used to initiate a trick.
A trick initiated with an ollie, the back foot then planting on the ground and pushing off while the board is controlled by the front foot and some kind of grab; the trick is landed with both feet on the board.
A grind on the back truck, with the nose pointing forward, down, and toward the obstacle.
A rail or bar that is not sloped down stairs or an incline.
Any flat surface at the bottom of a transition.
Skateboarding without any obstacles, with the exception of something to trick over.
These appear as clean spots on your dirty wheels as a result of the dirty urethane being rubbed off by the wheels sliding on some surface.
To flip your board is to make turn on its lengthwise axis, as in a kickflip or heelflip; to flip your body is to go head over heals as in a McTwist.
A fliptrick is a move that involves the board spinning on any or a variety of its axes.
To break a board in half.
Footage / Footie
Skateboarding captured on tape.
The name given to a frontside ollie 180 with a kickflip.
An indy grab while airing frontside.
Any variety of box (usually wooden) with grindable and slidable surfaces.
A distance between two riding surfaces which skaters ollie over, and often do other more sophisticated tricks over.
A caballerial with a mute grab *Lance Mountain and Neil Blender gave this trick its name after being humble enough to call their version of a caballerial "gay".
Amazing, Sick, Rad.
You are goofy footed if you normally skate with your left foot on the tail.
Using either hand to grab anywhere on the deck while in the air.
Any variety of tricks where the hanger(s) of the truck(s) grind(s) along the edge of an obstacle.
A sandpapery sheet with strong glue on its underside, put on the top of a deck for grip and control.
Grommet / Grom
Little kid skaters.
The name given to a fakie ollie 180.
Halfpipe / Vert Ramp
A ramp composed of a flatbottom with concave transition leading to vert on both sides.
A rail that is down stairs or an embankment and is of at least moderate height.
While trying to drop back in off of the coping after completing a trick, the truck that was above the coping does not clear it on the way back into the transition; this often results in a slam, but can be pulled off by some.
The largest part of the truck, it contains the axle, pivots on the baseplate, and is used to grind on.
A trick consisting of a frontside 180 pop shuvit and a kickflip.
The nuts and bolts of your skateboard.
The rotation of the board around its lengthwise axis as a result of kicking your front foot off the toe edge of your board.
The junction of two banks, transitions, or other riding surfaces which meet at an angle, usually anywhere from slight (300 degrees) to right (90 degrees); these angles are ridden, grinded, and flown over.
An ollie off of a hip.
A large, painful strawberry bruise on the hip which often becomes a hematoma, or a swelling of blood; avoid at all cost.
A grind starting with an ollie 180, then the back truck (which is now in front) is placed on the obstacle with the nose pointing back, down and towards the obstacle.
This trick can be performed using either your front or back foot, and it entails wrapping the nose or tail around its respectful foot 360 degrees.
When either airing forward or backside, grab your toe edge with your back hand and poke your nose out.
A trick that entails getting upside down and supporting yourself on one hand, usually on the coping of a ramp, as the other hand performs a grab.
A mute grab, tweaked frontside 9090.
A ledge that continues out laterally as an adjacent staircase or bank goes down.
Grab heel edge near the front wheel with your front hand and kick your front foot off in front of you.
see crooked grind
The rotation of the board around its lengthwise axis as a result of kicking your front foot off the heeledge of your board.
A trick consisting of a fully rotated kickflip that is then kicked with the front foot on the dark side of the deck to send it flipping back in the same direction that it came from.
The bolt that holds the hanger to the baseplate.
The nut that, on most trucks, screws on to the tip of the kingpin that sticks out through the bushings; on other trucks, the nut is held in place by a mold on the underside of the baseplate, and the kingpin is inserted down through the bushings rather than up (ex: Grind King); it is usually a 9/16" hex.
A rail that is kinked or bent, increasing its difficulty.
To perform a trick successfully.
Any trick that is executed after the board has reached its peak height in the air, or after another trick without first touching the ground.
A ramp used for launching a skater in the air.
Any raised surface used for grinding and sliding.
Grabbing heel edge while airing frontside *Invented by Neil Blender who said you have to lean into it, though nowadays it is spelled as Neil's first name written backwards.
The edge of any obstacle that a skateboarder rides; on ramps, the lip usually is completed with coping; on a bank or curb, the square or angled corner is the lip.
A slide in which the tail of the board goes up and over the obstacle and the board slides between the two trucks.
A skater is local to a spot if he lives nearby and is skating it and ripping it all the time.
see Hang up
The act of getting your board into a slide or grind position in a way that is most stable, allowing for a lengthy maneuver.
A madonna air with no grab.
Grab heel edge near the front wheel with your front hand and kick your front foot off behind you; this trick is often done to tail smack on the way back into the tranny Tony. Hawk himself named this one after a singer as trendy as the trick itself.
A trick in which the skater balances his weight over the back truck, keeping the front wheels off of the ground.
Any raised surface where a skater can ollie on to one section, and drop off another; such obstacles are used for manuals and for doing tricks onto and tricks off of.
Grabbing your heel edge with your front hand and pulling that edge up towards your back *named by Neil Blender who described this grab as the method for getting higher air.
Similar to a halfpipe, but smaller, with mellower transition and no vert.
Millimeter, the standard unit of measurement for the diameter of a wheel.
You are mongo footed, or “pushing mongo”, if you are using your leading foot, the incorrect one, to push.
Mounting bolts come in 1/8” increments from 7/8” up to 1 ¼” for standard setups; four are used to mount each truck, and they come in either allen or phillips head; their corresponding nuts are 3/8" hex.
The two sets of four holes drilled through your deck.
Grab your toe edge with your front hand while airing backside *named after Chris Weddle, a deaf mute known for being one of the first skaters to execute this trick.
Any trick that entails the front foot stepping off of the board and onto the ground while the back foot initiates any of a number of tricks such as ollie, 180, pop shuvit, etc.
An ollie off of the nose of the board rather than the tail *originated by Natas Kaupas, it is short for nose ollie or Natas ollie.
The part of the deck in front of the most forward two mounting holes which is steeper and longer than the tail.
A very short nose grind involving a quick bonk of the front truck on an obstacle.
A grind on the front truck, with the tail pointing up and back.
Nose manual / Nose wheelie
A manual performed on the front truck rather than the back.
A stall in the nose grind position, usually involving an indy grab for control.
A slide on the nose of the deck.
Any object that you can incorporate into a skateboarding trick.
Used to describe a trick or skater or pretty much anything that is representative of an older, nearly outdated style.
The basis of most other tricks, it entails using your back foot to smack the tail of your board against the ground while your front foot pulls the board up into the air. Invented by Alan Gelfand.
Short for over vert, a transition that goes past vert so that the face of the transition is actually facing slightly down.
Pig /Five0 /PoPo
Derogatory terms for peace officers.
A trick or part of a trick where the back truck is grinding atop an obstacle for just a moment before the trick's completion.
The cup molded into the baseplate that the rounded extension that sticks out from the hanger rests and pivots in.
This game is also called horse; someone starts off the game by doing a trick; if they miss, it's the next person's turn to try their own trick; if they land it, everyone else has to try it and whoever misses gets an S; the winner is the last one not to spell out the full word.
A sheet of wood used to make a deck; standard decks are 7 ply, but they can range from 6 to 9 plies with varying strengths and weights.
Riding up and off of a pole bent diagonally out of the ground.
A trick in which the board is popped in the air where it rotates along its vertical axis.
Someone who poses as a skateboarder, or anyone who tries to be something they're not.
Popular a few years ago, and still today with a lot of grommets, it entails putting pressure on the correct spot of the tail to make it flip around without hardly leaving the ground.
Your board is primo if it is resting on its side, axles running vertically.
A skater who is so good, companies want to put his/her name on their products.
A girl who likes hanging around with pro skaters.
Flexing your legs at the right spot on a transition to build up speed.
With one foot on the board, the other pushes along the ground to get speed.
A pyramid shaped obstacle with a flat top.
A ramp with only one concave transition (two quarters positioned facing each other would make up a vert or mini ramp, minus the connecting flatbottom).
Any type of railing of any size, material, and height.
A certain genre of skaters known for their laid back style, high ollies, dreadlocks and pot smoking abilities.
You are regular footed if you skate with your right foot on the tail.
A trick that is added on to the end of any other trick, and it means to spin one's self and the board 180 after completing the initial trick.
A really good and consistent skater.
Rubber or plastic spacers used between the baseplate and the darkside of the deck for a softer ride, to keep mounting hardware from loosening, and to prevent wheelbite.
Grab your heel edge with your back hand, in front of your back leg.
Once in the air, putting both feet on the tail facing lengthwise and grabbing the nose with both hands, keeping one's body as straight as possible so one looks like a rocket.
A smooth convex transition going from a flat platform into a steep transition.
Sack it / Nut it
To land on an obstacle usually a narrow one like a handrail, right on your jewels.
A grind on either truck, with the opposite end of the board pointing forward, up, and towards the obstacle.
Any time a group of skaters get together at a spot.
A body varial while doing a trick.
Shifty / 9090
Shifting your board 90 degrees, with feet still in contact with the board, then bringing it back to starting position.
A sidewards reentry into a transition, which is then turned fakie.
A summer camp for skateboarders where street obstacles, ramps, bowls, and banks can be skated without hassle from cops, parents, etc.
Any tool made specifically for a skateboard.
An area, publicly or privately owned, that has a variety of obstacles designed specifically for skating, and where you are safe from tickets (unless the nazis in blue see you padless).
A term coined in the early eighties and made famous by Thrasher magazine, that catagorizes the bands whose members rode skateboards; could be any type of music, but is noted for its generally uptempo beats.
A hard fall.
A grind on a ledge without ollieing.
Any trick in which any part of the deck is sliding atop an obstacle.
A mute grab while airing frontside.
A grind on the back truck, with the nose pointing forward, down, and away from the obstacle.
Small washers placed on the axle on both sides of the wheels to limit friction.
To spin your board is to make it rotate on its vertical axis as in a pop shuvit.
A ramp consisting of two quarter pipes back to back with a narrow spine, usually coping, separating the two.
Having your skateboarding supported by someone or some company who gives you discounts or free product.
Sponsor me video
A video made by a kid to send in to a company to see if he has the skills to get sponsored.
Any place any where that has anything to skate.
Grab your heel edge with your back hand, behind your back leg.
The act of getting your board into a sliding or grinding position on an obstacle, without sliding or grinding.
The different ways you can stand on your board.
To land a trick solid and clean.
The part of a skatepark with obstacles that mimic those found while street skating.
Skating which is done using only those objects or obstacles found in the urban environment.
Small lengthwise cracks on your deck that extend from the mounting holes and are a result of the stress created by the mounting hardware.
Ollie and "overrotate a lipslide" so you end up grinding the back truck on cooping with the nose pointing down to the side you came from (https://www.youtube.com/watch?v=Kt4seZyxHx0)
When you fall on your elbow and it gets abnormally large.
You are skating switch when you are not using your predominant foot to initiate a trick.
The part of the deck in back of the furthest back two mounting holes which is shorter and more mellow than the nose.
A slide on the tail of the deck.
Grab your tail with your back hand.
Any trick that is usually performed on flat ground or on a fairly low ledge, that involves plenty of technical skill such as combinations of flips/spins and slides or grinds. Also, a skater can be called tech, or a tech dog, if they are partial to these types of tricks. (Daewon Song is a tech dog).
To pivot left and right on your back wheels, either as a means of acceleration or to keep your balance when landing a trick off center, tic-ing and tac-ing your wheels to the ground.
To a skater, tools are any of the following: a phillips head, hex key, 3/8" wrench, 1/2" wrench, or 9/16" wrench, or anything else that can be used on a skateboard.
The top ply of the deck.
Whenever a skater transfers from one area to another; ex: from one ramp to another, approaching an obstacle from one side and riding away on the other side, etc.
Any surface for skating that is not horizontal or vertical.
A trick is any maneuver performed on a skateboard.
see Double set, and go from there.
The axle assembly, made up of the following: hanger, baseplate, axle, kingpin, bushings, axle nuts, bushing cups, and usually speedwashers.
Grabbing your toe edge right near the back wheel with your back hand and pulling the board back as you push your knees forward.
To add style to a trick be exaggerating or contorting it.
Varial / Shuvit
The spinning of the board along its vertical axis, without popping the board in the air.
Getting all four wheels on a vertical wall before ollieing.
A trick entailing riding your board on a very steep or vertical wall.
Two launch ramps, touching at one corner, with a triangle shaped platform between them.
Skateboard wheels are made of urethane; four of them let the skateboard roll.
When too much weight is applied to one side of the board, causing the darkside of the deck to touch a wheel and stop its rotation.
The marks on the darkside of your deck made by wheelbite scraping the paint off the deck.